Thursday, May 2, 2013

~Thrifty Thursday~

I hope today's project inspires you to think outside the box.
Here was my piece I started out with.

Today I am turning this old wood crate into a pet feeder.
I had been looking for a while now at elevated pet feeders because I read so much about how they are better on your pets joints, digestion, and everything really.
I didn't want a standard off the shelf one,
{and I didn't want to pay retail}

so I decided to turn an old wood crate I got at a garage sale for $7 into one.
You could use old soda crates too, which would be very fun.

~Here's the scoop~

For my size dogs
 {we have 2 yellow labs}
I read the height should be around 18"
To elevate it, I added casters to the bottom.

These were a bit pricey at $10 a piece.
X four that is $40.00, but I think worth it in the end.
It adds that industrial vibe and brings it to the right height.

To attach the casters , I flipped my crate upside down and measured in a 1/2" from each corner edge and made a mark.

The holes were too big on the casters so I added washers so the screws would fit.

Once those were all in place I worked on the top.
I didn't have one big piece of wood to cover the top so I had to join 2 pieces together.
I used barn wood, but you could use any kind of wood.
I laid my top pieces upside down and marked a spot in the middle and drew a line. 
I did this at either end as well. 
This is where you will be joining the wood together.

I used 3 scraps of wood and my air nailer to attach the strips
 that will now hold the 2 pieces of the top together.

Now you are going to measure and make templates for where your bowls will go.
Make sure your bowls have a rim, or they will fall right through the hole.
I had 2 white bowls from Walmart that I decided to use. 
I made a template by tracing the top of the bowl onto card stock and then cutting it out about a 1/2" smaller all the way around.

Now lay your templates down on the back of your top and trace around with a sharpie.

Now it is time to cut out the holes with a jigsaw.
But first, you need to drill a hole in the center of each as a starting point for your jigsaw blade.

Cut out along the lines~shoes are optional.

I ran into a problem here. 
My jigsaw couldn't make the full circle cut because my wood pieces joining the top together were in the way.
I had to remove them, then cut the holes, then put the wood back on.
So, in hindsight, I would cut the circles out first and then add the joining pieces.
Hope that makes sense!

After that you can sand any rough edges and fit your bowls. 
Some adjusting may be necessary.
It's better to cut the hole too small and have to go back and cut more out.
If you cut the hole too big, you are outta luck.

 This is the back with the top placed on.
As you can see there is a gap. 
The hinges I had on hand were small, so I filled in this gap with a piece of scrap wood so that the screws in the hinges would have something to screw into.

You want to screw in a hinge to the back on either end.
Now your lid will flip up for storage inside!

Are you ready to see it all finished?

 I added this old latch just for decorative purposes.

 I love that all the dogs toys can be stored neatly inside!

 And I love how "rough" it is, old nails and all!

 The best part is that the puppy approves.....

 as well as the old man.

Cost of this pet feeder came in at around $50.00.
~happy dogs~priceless~
Bet you couldn't buy it for that!


Unknown said...

wow! I love your feeder box! pet and environment friends, and beautiful!

Nest said...

I am totally lovin' your Thrifty Thursday posts! I love the casters and our Home Depot carries the same ones for 3.97 each! Thanks for sharing your amazing ideas~

Lynda @ Happenstance Home said...

Love what you do Melaine. I bet your pups love it!!!

tiffany said...

So creative!! This would be perfect for my two huskies. I may have to give this one a go!

Hillary said...

Super cute

Acorn to Oak said...

I LOVE this project! I've been wanting to get or make a raised dish holder for our dog too. And, like you, I don't want a standard, not very attractive, off the shelf kind. I would love to make this one. Just not sure where I might find one of these old boxes. Congratulations! Awesome job! Oh...and your dog is adorable! Have a great day!

AntiqueChase said...

I love this! and you're right casters are so much money. I try to find them at garage sales. I got lucky once.

Lolo @ The Adventures of Stig and Lolo said...

So cute! I love that you can store toys and extra snacks in there too :) Love this idea Melaine!

pam {simple details} said...

SO dog-gone cute!! :)

Anonymous said...

So cute!!


Unknown said...

Love it! Perfect with the chalk board wall :)

Between You and Me said...

love the project.....not sure if I ever put it together that y'all had 2 dogs. They're beautiful. :)

Mary Ann Pickett said...

You are brilliant! Lucky dogs.

Content in a Cottage said...

I'm so impressed that you have a nail gun and a little jealous too. Nice job.

Anonymous said...

Hi, I do believe this is a great site. I
stumbledupon it ;) I'm going to return once again since I bookmarked it. Money and freedom is the greatest way to change, may you be rich and continue to guide others.

Here is my website - All Natural Cleanse

Debra said...

Wow I just love this, I have smaller doggies so I will have to make a smaller one but love it. :-) Thanks for sharing.

Bilibili said...

Yeezy boost 350 v2
Retro Jordan 11
Jordan Retro 11
Kyrie Irving Shoes
Jordan 4 Retro
Red Bottom Shoes For Women
Yeezy boost 350 v2
Air Jordan 11
Pandora Outlet
Jordan Retro 9

Related Posts Plugin for WordPress, Blogger...